Turris 1.x routers fails to boot kernel 5.4 and kernel 5.10
While using hbd
branch on Turris 1.x router where is kernel 5.4 and I tested also kernel 5.10, blue routers Turris 1.x fails to boot.
U-Boot 2015.04-04654-gbcfb33e-dirty (Jun 26 2015 - 12:50:49)
CPU0: P2020E, Version: 2.1, (0x80ea0021)
Core: e500, Version: 5.1, (0x80211051)
Clock Configuration:
CPU0:1200 MHz, CPU1:1200 MHz,
CCB:600 MHz,
DDR:400 MHz (800 MT/s data rate) (Asynchronous), LBC:37.500 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
wdt status 00000005 reset
Watchdog enabled
Board: TURRIS CPLD: V4.1 PCBA: V4.0
Error, wrong i2c adapter 2 max 2 possible
in: 56
out: 0
io_config: 255
rom_loc: nor upper bank
SD/MMC : 4-bit Mode
eSPI : Enabled
I2C: Error, wrong i2c adapter 2 max 2 possible
ready
SPI: ready
DRAM: Error, wrong i2c adapter 2 max 2 possible
Detected UDIMM 9905594-003.A00G
WARNING: Calling __hwconfig without a buffer and before environment is ready
WARNING: Calling __hwconfig without a buffer and before environment is ready
2 GiB (DDR3, 64-bit, CL=6, ECC off)
Flash: 16 MiB
L2: 512 KiB enabled
NAND: 256 MiB
MMC: FSL_SDHC: 0
PCIe1: Root Complex of mini PCIe SLOT, no link, regs @ 0xffe0a000
PCIe1: Bus 00 - 00
PCIe2: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe09000
02:00.0 - 168c:0030 - Network controller
PCIe2: Bus 01 - 02
PCIe3: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe08000
04:00.0 - 104c:8241 - Serial bus controller
PCIe3: Bus 03 - 04
Error, wrong i2c adapter 2 max 2 possible
In: serial
Out: serial
Err: serial
Net: Phy 5 not found
PHY reset timed out
eTSEC1
Error: eTSEC1 address not set.
, eTSEC2
Error: eTSEC2 address not set.
, eTSEC3 [PRIME]
Error: eTSEC3 address not set.
Hit any key to stop autoboot: 0
BOOT NAND
reading zImage
5537311 bytes read in 246 ms (21.5 MiB/s)
wdt status 00000003
reading fdt
12147 bytes read in 14 ms (846.7 KiB/s)
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 02100000 ...
Image Name: Linux-5.10.52
Created: 2021-07-27 23:20:06 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 5537247 Bytes = 5.3 MiB
Load Address: 00c00000
Entry Point: 00c0029c
Verifying Checksum ... OK
## Flattened Device Tree blob at 02000000
Booting using the fdt blob at 0x2000000
Uncompressing Kernel Image ... OK
Loading Device Tree to 03ff9000, end 03ffef72 ... OK
WARNING: could not find compatible node fsl-usb2-dr
Maybe some insights could be provided by #124 (closed)
Reproduced by me and @jbetik